End of life
End of life
The DVC 310 has been phased out and replaced by the DVC 550 in DEIF's product programme.
If you already have an DVC 310 and need a replacement product, please contact DEIF at +45 9614 9614.
Related applications
Product videos
Cases
CASE: Critical power system for leading data centre
Buy these products instead
Digital voltage controller DVC 550
- Unique CANbus integration between DVC 550 and AGC genset controller
- Start management capability with start on threshold, soft start and close before excitation (run-up sync)
- Intelligent drying and ventilation mode for generators
- Short circuit limitation
- Loss of voltage sensing alarm
- Over/under excitation limitation
- Optimises genset performance and size using engine help functions
- Load acceptance module (LAM) assists the generator during heavy loads
- Negative forcing to avoid voltage peak during load sheddin
- U/F ramp
- Soft voltage recovery
- Stator current limitation
- Settings from AGC genset controller shared with the DVC 550 via CANbus
- Grid code compliant VDE410 and VDE4105
Advanced Genset Controller AGC 200
- Mehrere Betriebsarten in einer Software
- Synchronisation von bis zu 56 Schaltern in einer Anlage
- Multimaster-Power-Management
- Lastabhängiger Start/Stopp
- Last-Management
- Prioritätenwahl (manuell, relative Betriebsstunden, absolute Betriebsstunden, Kraftstoffoptimierung)
- Kompatibel mit AGC-4
- Programmierbare Logic (M-Logic)
- Konfigurierbare Eingänge/Ausgänge
- Schutz für Motor, Generator und Verbraucher
- Spannungsmessbereich: 50 bis 690 VAC (UL/cULgelistet, 50 bis 600 VAC)
- Unterstützung aller gängigen Motortypen durch J1939-Motorkommunikation
- Ausgabe der Motormeldungen in Klartext
- Fernsteuerung über TCP/IP, RS-485 Modbus oder GSM-Modem
- High-Speed-USB
- Mehrsprachige Benutzeroberfläche
- -40ºC Betriebstemperatur
- Schutzart IP 66
- SD-Kartenslot für Langzeit-Logbuch
Automatic genset controller AGC-4
Automatic genset controller (AGC-4) - Features
- Up to 32 gensets in one plant
- The intuitive, preprogrammed touch display saves you time and smoothes operation
- Four general purpose PID regulators that control auxiliary systems
- Synchronises up to 56 breakers in one plant
- Multiple operating modes in one software
- Multi-master power management
- Load-dependent start and stop
- Load management
- Emulation for fast training and I/O test
- Automatic Mains Failure sequence
- Complies with: VDE AR-N 4110 (medium voltage, Germany), VDE AR-N 4105 (low voltage, Germany), EN 50549-1:2019 (Europe), ENA EREC G99 (United Kingdom). Option A10 required.
- Approved by TÜV and UL
- Tier 4 final support
- Hot standby for full system redundancy
– change to backup genset controller on the fly - Redundant CANbus for power management
- Close Before Excitation/Run-up synchronization
– synchronisation from 6 seconds - Fully compatible with AGC 150 and AGC 200 controllers
- Suitable for hybrid power solutions fitted with ASC-4 controllers
Advanced Genset Controller AGC 150
- Synchronization
- Power Management Core (32dg)
- -40 degree support
- PLC
- Engine and Generator protection
- Engine CANbus
- Front mount
- Additional CANbus based I/O (9 x CIO modules)
- DEIF digital AVR DVC550 support
- Multi purpose PID´s
- Tier4 final/stage5
- Emulation
- Hybrid EMS support
- Fuel optimisation
Batterieladegerät DBC-1
- Automatische elektronische Schutzfunktionen
- Automatischer Restart nach Fehlerbedingung
- Alarm
- Automatische Lastreduzierung bei hohen Umgebungstemperaturen
- LED-Anzeige von Fehlern, Starklademodus und Normalbetrieb
- Starklademodus
- Einstellbare Ausgangsspannung
- Keine beweglichen Teile - keine Wartung