Multi-line 2 BGC Application Software series 2.x. 2.12.0

2.12.0

21.10.2005

New features:

• Short time parallel added
• VDE0108 sync. type updated

Changes:

• Running, MB, GB offset updated
• Password handling updated
• Fuel pump logic/alarms updated
• Short circuit precision updated
• Hysterisys added to running detection
• "Reset analogue input" functionality updated
• M15 scaling added
• FC updated on DI

2.50.3

13.04.2015

This software applies to the following DEIF products:

Multi-line 2 - BGC

Multi-line 2 - BGC-L

Changes:

• 1- Update of self-check functionality

2.50.2

14.03.2013

Changes:

• Start attempt settings was ignored.Corrected.
• Minimum load in AMF was ignored.Corrected.

2.50.1

30.10.2012

• The breaker did not open in Semi auto AMF mode. Only L1 decides if the frequency has dropped 0.5 Hz. Corrected.
• The ramp down speed setting was ignored in Island mode and just ramped down as fast as possible. Corrected.
• The genset stopped deloading and opened the breaker if it was 0.5 Hz over nominal settings. Corrected.

2.50.0

12.08.2010

New features:

• VDO 3 can be used as temperature AND a Fuel sensor.

Changes:

• Prompt for password when leaving block mode. Password level set in parameter 4901.
• Ramp function implemented in Peak Shave mode.
• Stop conditions in peak shaving improved.
• VDO 2 calculations for level switch corrected.
• MTU ADEC CAN communication improved.

2.40.2

17.10.2008

Improvement:

• Stop command for Volvo and Scania engine communication changed

2.40.1

15.08.2008

• Translations function corrected and max. number of languages reduced from 11 to 9

2.40.0

29.07.2008

New features:

• Support of communication whit MTU-ADEC

Changes:

• Volvo Penta EMS2 and SCANIA speed control updated.

2.31.3

12.12.2007

• H2 option protocol now supports Modbus function 05 and 06.

2.31.2

29.10.2007

• Password max limit changed to 32000.
• Volvo Penta EMS2 preheat function updated.
• Fire pump cooldown timer function updated.
• M15 Analoge input measurements improved.

2.31.1

04.09.2007

• Improved ramp up handling.
• Volvo Penta EMS2 comm. error alarm updated.

2.31.0

19.06.2007

New features:

• Regulation of reactive power, trough H2/H3

Changes:

• Improved Ramp up delay handling.
• Horn relay updated.
• Improvement of external comm. enable input

2.30.3

16.01.2007

Changes:

• Improved vector jump calculation.
• BGC-L Input list updated

2.30.2

23.10.2006

Changes:

• Handling of nominal power below 100kW updated.

2.30.1

28.09.2006

Changes:

• GB handling updated.
• IO view in util. SW updated.

2.30.0

05.09.2006

New features:

• BGC-L for selected markets added.

Changes:

• Frequency measurements >70Hz updated

2.21.2

26.06.2006

Changes:

• GB operations adjusted upon back-sync-error.
• Handling of MB close-failure updated.

2.21.1

08.03.2006

Changes:

• Selection of Scania EMS 2 from USW updated.

2.21.0

24.02.2006

New features:

• Scania EMS2 support added.

Changes:

• Limit relay function updated.
• Maximum frequency readout handling updated.
• Volvo Penta EMS2 frequency change updated.
• Power up sequence updated.

2.20.0

13.01.2006

New features:

• Parallel enable added for Mains protections.
• Channel 4800 (GOV / AVR relay setting) removed. Old relay settings was: GOV up: Relay 6, GOV down:
• Relay 7, AVR up: Relay 8, AVR down: Relay 9.
• Channel 4801-4804 added for GOV / AVR relay setting.
• Auto start/stop input enabled in AMF.
• Virtual input: Semi start, Semi MB off, Black busbar enable updated.
• MLogic updated and new settings added.
• Various Mlogic input / output added.
• H5 Volvo Penta EMS 2 added.
• Test mode setting: Simple, Full and Parallel.
• Engine control relays configurable from MLogic when using Volvo Penta EMS 2
• Self acknowledge added in USW. Channel 4452 "Auto reset warning FC" is removed.
• Compact breaker handling added.
• Manual control of GOV / AVR added for SEMI, TEST and AUTO.
• DI alarms 1960-1990 added.
• Actual language present in USW parameterlist.
• Earth fault alarm and handling added.
• Command timers output added to MLogic.
• Selectable number of languages supported.
• Service and master password settings available in JUMP menu.

Changes:

• Overload 1 timer updated.
• Horn function updated.
• Gen-bar LED handling updated.
• Short time parallel updated.
• Semi mode handling updated.
• Functionality of channel 2050 updated.
• AVR reg. failure handling updated.
• Mains fail handling updated.
• MDEC protocol updated.
• Scania protocol updated.
• Back sync OFF functionality updated.
• MB alarm updated.
• Running detection updated.

2.12.2

28.11.2005

Changes:

• MLogic command outputs updated.

2.12.1

17.11.2005

Changes:

• Short time parallel updated
• MLogic "MB synchronizing" updated
• Minor updates

2.12.0

21.10.2005

New features:

• Short time parallel added
• VDE0108 sync. type updated

Changes:

• Running, MB, GB offset updated
• Password handling updated
• Fuel pump logic/alarms updated
• Short circuit precision updated
• Hysterisys added to running detection
• "Reset analogue input" functionality updated
• M15 scaling added
• FC updated on DI

2.11.1

30.06.2005

Changes:

• Extended stop executed if running detection is lost

2.11.0

22.06.2005

New features:

• MB trip failclass can be set in mains/bus protections
• EIC alarms can be set to RUN activation

Changes:

• GB trip stop failclass handling updated
• Handling of overlap updated
• Handling of view 3 updated

2.10.0

New features:

• Support for MKIII PCB
• Firepump cool down timer added
• Delta V operation mode added

Changes:

• Idle mode updated