Multi-line 2 Standard Application Software series 2.3x and 2.4x

You’re about to download Multi-line 2 Standard Application Software series 2.3x and 2.4x

You have chosen to download our software.

Within a few seconds, you will receive an email containing a download link.

Having trouble using the software? Please contact support@deif.com. 

Best regards, 

DEIF A/S

The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software

This software applies to the following DEIF products:

You’re about to download 2.42.8

The main changes implemented since the last version are as follows:

This software applies to the following DEIF products:

  • Multi-line 2 - GPC v.2.xx
  • Multi-line 2 - GPU v.2.xx
  • Multi-line 2 - PPU v.2.xx

Change:

  • Update of self-check functionality
Ver. Date Description

2.42.8

30.03.2015

This software applies to the following DEIF products:

  • Multi-line 2 - GPC v.2.xx
  • Multi-line 2 - GPU v.2.xx
  • Multi-line 2 - PPU v.2.xx

Change:

  • Update of self-check functionality

2.42.7

19.09.2011
  • Running hour counter overflow at 32500hours corrected.

2.42.6

27.04.2011
  • Analogue output (option F2) improved.

2.42.5

24.02.2010
  • Removed bumb from regulator first time GB closes.

2.42.4

22.10.2009
  • Df/dt protection improved.
  • Vector jump protection improved.
  • Unit psi implemented for analog input

2.42.3

20.03.2009
  • Writing to control registers no longer depends on H options.
  • Low current measurements improved.
  • Handling of synchronizing failure improved
  • Parameter 2260 is now available in DEIF Utility Software.
  • Ability to show large negative power improved.
  • Maximum timer values for stop failure and run status set to 3000 seconds.
  • Unbalanced current calculations now relates to the nominal current setting.
  • New modbus measurement (03h) at address 65 indicates PF with sign. Address 11 is without sign.

2.42.2

23.11.2007
  • Sync. using step up transformer improved.

2.42.1

29.10.2007

New features:

  • Protection level "Over load 3" added.

Changes:

  • "No Regulation" was logget twice.
  • Password max limit changed to 32000.
  • kWh counter output did not work correct after reset of counter value.

2.42.0

31.08.2007

New features:

  • Ramp up in loadshare mode.

Changes:

  • USW did not show password correct if language other than English was selected

2.41.2

25.05.2007
  • Improved frequency protection.

2.41.1

08.05.2007

Changes:

  • Max setting for starter ON time 180s.
  • Improved alarm log handling.
  • Improved vector jump calculation.
  • Show terminal 43 - 53 at USW only if load share board is present.
  • Could not access menu 4960 via jump.
  • USW did not show menu 2275.
  • Unbalance voltage calculations improved.
  • Zero sequence calculations improved.

2.41.0

23.10.2006

Changes:

  • EF5 option implemented
  • Handling of option M15 changed
  • Inhibit of BB alarms U>, f>

2.40.1

03.10.2006

Changes:

  • Accuracy of reactive power measures improved
  • Accuracy of I>> measure improved

2.40.0

18.08.2006

New features:

  • Use of step-up transformer. 

2.32.6

27.04.2006

Changes:

  • Possibility to set option G1 modified

2.32.5

08.03.2006

Changes:

  • Option O1, cascade control has been trimmed

2.32.4

02.01.2006

Changes:

  • Analogue output for PF modified
  • Interface between USW and GPU settings modified
  • Menu's for M13 modified
  • Handling of relay 10...13 modified
  • MDEC protocol handling modified
  • GPU - relay-functionality modified

2.32.2

10.10.2005

Changes:

  • Handling of option C2 - alarms during genset stop sequence changed
  • Scaling of the controller output shown in the USW changed
  • Mode-handling via terminal 43 is changed
  • Handling of downloading changed parameters changed
  • Option O handling of waterlevel controller changed
  • Factory settings for negative + zero sequence changed

2.32.1

27.06.2005

Changes:

  • Water-level regulation updated

2.32.0

30.05.2005

New features:

  • CanOpen protocol: Zero-sequence U and I failure added

Changes:

  • RPM measurements updated
  • Option O - regulator start adjusted
  • Minor changes in menus and min/max settings

2.31.2

04.03.2005

Changes:

  • Handling of asynchron generator changed
  • Option O - regulators for water-turbines adjusted
  • Minor changes to menus and min/max settings

2.31.1

14.12.2004

Changes:

  • Relay3 functionality regarding alarm/reset adjusted
  • Volvo Penta engine protocol adjusted
  • Minor changes in menu texts

2.31.0

24.11.2004

New features:

  • SMS functionality extended
  • Option H5 - MDEC engine interface extended
  • Splitphase/single functionality modified
  • Limit switches functionality extended

Changes:

  • Relay output functionality extended
  • Analogue current output for AVR/Gov limited
  • GDU interface adjusted
  • Some menus in some languages adjusted
  • Some minor adjustments of set-points limits

2.30.3

12.08.2004

Changes:

  • Handling of The emergency stop functionality in regard to option M20 is changed
  • Reverse power alarm - max timer setting is extended
  • Alarm messages displayed in USW is now displayed in the chosen Multi-line 2 language
  • German texts are adjusted
  • The Modbus ASCII mode is improved
  • Eventlog view in USW is improved
  • Update of number of CB operations is changed
  • Negative sequence voltage functionality improved at high voltages
  • Possible overflow in scaled analogue input is removed

2.30.1

15.06.2004

Changes:

  • Frequency regulator adjusted for perfect performance
  • Initialisation of loadshare lines are optimised
  • Run coil functionality adjusted

2.30.2

15.06.2004

Changes:

  • Option H4 CCM: Optimised and extended possibilities
  • Modbus possibilities extended 
  • Translations of German and Spanish completed

2.30.0

14.04.2004

New features:

  • Option H4 CCM-communication read/write functions extended
  • Option H4 CCM-comminication heartbeat handling added
  • Option H5 Can-bus Engine interface implemented, supporting:
    MDEC 2000/4000 M.302
    MDEC 2000/4000 M.303
    DDEC
    EMR 
    JDEC
    Volvo Penta
  • Option H6 Cummins engine communication added
  • Modbus protocol extended

Changes:

  • Running detection for disconnection of starter is changed
  • Configurable display text for PT100 added
  • Some setpoint ranges are extended
    Option O Waterturbine - minor changes of functionality

2.20.1

11.02.2004

Note: When updating a previously version of the application software, which is using the engine start/stop logic, with this new version (2.20) will requirre enabling of engine start/stop logic after software updating. Default the engine start/stop logic is disabled after updating the software. To enable it jump to menu 6030 and activate the engine start/stop logic - not as previously stated menu 6000.

New features:

  • GSM Modem connection supported
  • Automatic transmission of SMS in case of an alarm
  • Voltage transformer ratios different for generator and busbar supported
  • Display texts configurable for readings as well as alarms
  • Selection of monitoring of phase-phase or phase-neutral voltages
  • Counters for kWh export, kWh import, kvarh export and kvarh import on Modbus.
  • Option M20 added. Engine I/F boards with or without engine start/stop logic selection. 
  • Dual alarm settings for all analogue values (4-20 mA, PT100, VDO, RPM)
  • Modbus ASCII mode added
  • Catarpillar PWM output improvements regarding regulator setting
  • Zero sequence alarms for voltage and current
  • Possible to check version of basis software
  • Serial modbus communication optimised

Changes:

  • ML2 will send a login string when a CCM-comm. string is created
  • 2nd parameters for some alarms are changed
  • Alarms can be ack. via Comm regardless of the External comm. control input.
  • Option O - water turbine is adjusted
  • PF readout in display is adjusted
  • Scaling in the USW on some points are adjusted
  • Conditions for Mode 3 is adjusted
  • Conditions for manual mode are adjusted
  • Cooperation between Option D1 and Option O together with option E1 or EF4 is adjusted
  • Menu selection with Option EF4 is adjusted
  • Menu selection with Option EF3 is adjusted
  • High overcurrent adjusted in regard to settings.
  • Parameter index for CANopen option adjusted

Note: When updating a previously version of the application software, which is using the engine start/stop logic, with this new version (2.20) will requirre enabling of engine start/stop logic after software updating. Default the engine start/stop logic is disabled after updating the software. To enable it jump to menu 6000 and activate the engine start/stop logic. 

Auf dieser Seite können Sie Software-Updates für Ihr(e) Produkt(e) herunterladen und sich verschiedene Utility-Tools und Add-ons beschaffen, die Ihnen beim Einrichten und Konfigurieren Ihres Produkts/Ihrer Produkte sowie bei der entsprechenden Fehlersuche behilflich sein können.

Beachten Sie bitte, dass nicht alle unsere Produkte vom Benutzer aktualisiert werden können. Es werden auch nicht alle unsere Produkte mit einem Utility-Tool geliefert. Somit kann die Liste auf dieser Seite nicht als Übersicht unseres kompletten Produktsortiments angesehen werden.

DEIF registriert Ihren Download zusammen mit der verwendeten E-Mail-Adresse, um Ihnen auf Anfrage Informationen zu künftigen Updates zuzusenden.

DEIF kann nicht für die Folgen fehlgeschlagener Produkt-Updates oder die Nutzung von Utility-Tools haftbar gemacht werden. Auch haftet DEIF A/S nicht für die Folgen einer Verhaltensänderung von Produkten aufgrund eines Software-Upgrades. Es obliegt stets dem Anwender, vor der Inbetriebnahme die korrekte Einrichtung und Konfiguration sicherzustellen. Sehen Sie sich vor der Aktualisierung des Produkts das Versionsprotokoll der Software an.

Lizenzvereinbarung für den Software-Download von www.deif.com

Heruntergeladene Software bleibt Eigentum von DEIF. Die Software wurde möglicherweise nicht für gewerbliche Zwecke ausgegeben, sie wurde vollständig oder partiell geändert oder wiederverwendet oder sie wurde an jedwede Drittanbieter verkauft.Auf dieser Seite können Sie Software-Updates für Ihr(e) Produkt(e) herunterladen und sich verschiedene Utility-Tools und Add-ons beschaffen, die Ihnen beim Einrichten und Konfigurieren Ihres Produkts/Ihrer Produkte sowie bei der entsprechenden Fehlersuche behilflich sein können. 

Die aktuellste Version für volle Funktionalität

Wir empfehlen Ihnen, die von uns bereitgestellten Updates zu installieren, um so das volle Potenzial Ihres DEIF-Produkts nutzen zu können.

Die gesamte optimierte Software kann nach Belieben unter www.deif.com heruntergeladen werden. Navigieren Sie dazu zu „Software“ und dann zu „Software-Download“.

Bei Fragen oder Problemen beim Auffinden der entsprechenden Software für Ihr Produkt wenden Sie sich telefonisch unter der Rufnummer +45 96149614 an DEIF A/S oder an die jeweilige lokale DEIF-Niederlassung. Alternativ können Sie uns auch eine E-Mail an support@deif.com senden. Wir helfen Ihnen gerne weiter.

Press release, June 2015

Information on product improvement specifically related to “older” DEIF A/S ML-2 products.

Read more